2 * ap-gl/auth.c: small bugfix
4 2005-01-15 Roman Festchook
5 * src/ap-rrd.c: added utility to store stats from AP into RRD database
6 * src/wlan.c: added 'ACK timeout' additional info into [T] SIFS time (msec)
8 * configure.in, NEWS: version 1.5pre2
11 Note to SmartBridges PTE: you could have nice support in ap-utils
12 at cost of sending me one APPO sample. Since I actually have
13 no sample to test & verify on, all my support for airPoints is on
14 blind or 'someones trial and error report' basis. You should really
15 support OSS developers better way. Info about how to reliably load
16 airPoint PRO firmware to non-SB brand devices, based on the same HW
17 ref. design, would of course help too.
19 NOTE TO ALL USERS: IF YOU HAVE SMARTBRIDGES airPoint PRO (indoor or
20 outdoor) AND WANT BETTER AP-UTILS SUPPORT, YOU CAN SEND ME ONE SAMPLE
21 OF THIS DEVICE. OTHERWISE THERE WILL APPARENTLY BE _INCOMPLETE_ SUPPORT
22 EVEN IN FUTURE! THE LAST APPO I I'VE SEEN IN BAZAAR THAT I WAS PLANNING
23 TO GET IN ORDER TO IMPROVE SUPPORT IN AP-UTILS, HAS BEEN JUST SOLD
24 OUT, SO MY PLANS ARE GONE. I'M NOT WILLING TO PAY LIKE $350
25 FOR ONE SAMPLE JUST TO SUPPORT THE WORLD. SO UNTIL SOMEONE SUPPORTS
26 ME WITH SAMPLE DEVICE TO TEST ON, MY SUPPORT FOR SmartBridges
27 APPO in AP-UTILS IS _OVER_ (and this round of patches is apparently
28 the last effort to improve support in this area).
29 I'LL ALSO ACCEPT ANY DEVICE THAT USES THE SAME FIRMWARE / MIB
30 AS SMARTBRIDGES airPoint PRO.
32 You can contact me about the subjects above via e-mail at
33 <jr-aputils at cedric dot unob dot cz>.
35 Dedicated to memory of cat Micka, my pet.
36 * EZYNET-enhanced AP firmware is now freely available! Read more about
37 its availability, upgrade possibilities and caveats in README,
38 section 'Firmware available free of charge for ATMEL12350 MIB
40 * renamed all references of 'VERNET' to 'EZYNET' (true vendor name)
41 * renamed all references of 'TELLUS' to 'GEMTEK' (Tellus, SparkLan,
42 etc. appear to be GemTek subsidiaries or at least they seem to use
43 firmware from GemTek. If someone knows I'm wrong with this
44 conclusion, please let me know).
45 * note: my primary focus is on support for devices running firmware
46 0.2.x.x, equipped with flash memory AT29LV040A (TSOP1), and
47 second SRAM, such as Tellus A14, SparkLan WX-1590L, etc.
48 Easy way of how to tell that the device has second SRAM, is
49 presence of (poor, locky) web management interface. Older devices
50 with single SRAM may be supported too, but my older test equipment
51 is restricted to W-Link WEN2021 and I-TEC AP GOLD / blue, which means
52 that support for other old ATMEL flavours may or may not work,
53 despite all effort towards supporting them.
55 - added entries for supported APs: i-Tec AP GOLD (black front),
56 InterEpoch IWE1000A, OSBRiDGE m2410/p2410, SparkLAN WX-1590,
57 SparkLAN WX-1590L, D-com WX-1590 web, BOSSWAP
58 - the supported AP table is now sorted according to manufacturer name
59 - added section 'Firmware available free of charge for ATMEL12350 MIB
61 - made WARNING notices more accurate
63 - added entry with thanks to EZYNET
65 - reordered directory components so that 'intl' and 'po' will be
66 built as last ones. This helps on systems with old/broken auto*
67 tools, where building 'po' may fail (it still will do, but its
68 failure now wont prevent building other components).
69 * Documentation/mibs-atmel:
70 - created & populated with all AT76C510 MIB prototypes that should
71 be supported by ap-utils
72 * ap-gl/ap-gl.c, ap-gl/stations.c:
73 - backport of few changes from respective counterparts in src/,
74 to stay compatible with changed color scheme definitions
75 and format of 'Stations' output (btw, there is now no difference!)
77 - backported few non-invasive changes from auth.c
79 - added DONE_WRITING_APCONF & ERR_WRITING_APCONF, since they are
80 now referred from connect_options() as well as get_opts()
81 - added new structs AssociatedSTAsInfo_ATMEL410,
82 AssociatedSTAsInfo_ATMEL12350, NetworkSettings_ATMEL410_SBRIDGES
83 and NetworkSettings_ATMEL12350_EZYNET in favour of unified support
84 across most available vendor-enhanced MIBs
86 - connect_options() is now verbose about status of writing
87 ~/.ap-config file, through DONE_WRITING_APCONF & ERR_WRITING_APCONF
88 - bugfix: fixed ap_vendorexts[ap_type][] boundary check error;
89 no more segfaults when manually specifying MIB type as "ATMEL12350"
90 - bugfix: get_mib_details() no longer relies on OUI part of device's
91 eth. MAC address as authoritative info for MIB vendor extension
92 determination. This was 1. giving totally fake results
93 if someone changed device's MAC, and 2. giving false results
94 for people with devices whose firmware has had certain MIB vendor
95 extensions available (for example SparkLan users with GEMTEK
96 firmware). Autodetection should now work for much broader range
97 of devices with AP firmware.
99 - added functionality for HOME, END, PGUP and PGDN keys
101 - bugfix: in get_value(), use wmove()/wrefresh() instead of wechochar
102 with 0x08 char. (backspace) as parameter - this fixes visual effect
103 of disrespecting leftmost bound on platforms with older ncurses
104 - bugfix: get_mac() now forces user to specify all 12 numbers of MAC,
105 avoiding ambiguous results
107 - squeezed the number of wrefresh(menu) calls to a minimum
108 - mark and highlighting of current menu item are now
109 cleared/restored upon entering/leaving atmel_set_oeminfo()
110 * lib/oui.c: added OUIs:
111 - 000F3D (D-Link Corporation)
112 - 00112F (ASUSTek Computer Inc.)
114 - simplified & unified 'Stations' menu output section in
115 scroll_rows() - it is now used for all ATMEL AP types.
116 Part separately dealing with APs using SmartBridges firmware
118 - shorten screen output of print_top_rssi()
119 - bugfix: in scroll_rows(), clear_main(3) changed to
120 clear_main(row), to make the first-row offset of scroll list
121 really configurable (required by auth.c)
122 * lib/set_community.c:
123 - left boundaries of community fields now start at offset 37
125 - now also shows board VID & PID
126 - added possibility to configure # of calibrated channels
127 Reached 100% compatibility with original utility.
129 - removed RETRIES constant. Instead, snmp_retries now keeps
130 the default amount of retries. This was somewhat necessary,
131 as we may eventually influence amount of retries one snmp() call
132 will attempt, in src/aplink.c
134 - since test() is not yet ATMEL12350-ready, temporary kludge
135 has been added to disable this menu for devices with
138 - bugfix: fix utility crash, that could previously happen if
139 someone changed value of Fragm. threshold from default to
140 value < length of typical expected SNMP response packet,
141 on device managed with ap-config via wireless port.
142 The return value of snmp() is now checked against the number
143 of varbinds members entering snmp() (it covers return value
145 NOTE: IT IS _VERY_ UNWISE AND RISKY TO CHANGE 'RTS threshold'
146 AND 'Fragmentation threshold' VALUES ON DEVICE MANAGED VIA
147 WIRELESS PORT, SINCE THEY HAVE DIRECT IMPACT ON PACKETS TRANSMITTED
148 VIA WIRELESS PORT, AND IF THE VALUE IS BEHIND CERTAIN THRESHOLD,
149 THE DEVICE MAY BECOME COMPLETELY _UNMANAGEABLE_ VIA WIRELESS PORT.
150 If this happens and you have management access to the device
151 via wireless port only, you may try your favourite *-snmp tools to
152 restore RTS threshold and Frag. threshold settings to their
153 default value (2346), but if this fails, the only real way left
154 to fix these values would be through ethernet or USB port. Beware!
155 * lib/set_oeminfo.c, lib/sysinfo.c, lib/wlan.c:
156 - bugfix: changed assumption about selection of proper length
157 sysDeviceInfo OID - this cant be distinguished based on ATMEL MIB
158 type, since, for example, NETGEAR ME102 MIB has ATMEL12350 MIB, but
159 has length of this structure 128 bytes (which most ATMEL410 MIB
160 equipped devices have). Now the proper structure is selected
161 based purely on length of response returned on SysDeviceInfo
162 SNMP query - should 'fix' all places that deal with values
163 generated by query to SysDeviceInfo OID
165 - newly introduced. Embeds atmel_aplink(), which is bound
166 to 'AP link' entry in the 'Info' menu. This entry allows to
167 monitor link state of the device in APclient or WRepeater mode.
168 It will inform user whether the APclient device is actually
169 associated to the AP or not, and if yes, what is the RSSI level of
170 the link (as well as Link Quality in case of device with
171 SmartBridges firmware, or actual connection speed in case of device
172 with EZYNET firmware), MAC of joined BSSID, ESSID, and used
174 RSSI top value per entire measurement session is also available.
175 Since the RSSI indication may be somewhat unstable (at least
176 with EZYNET firmware), showing of RSSI average from up to
177 99999 samples has also been implemented.
178 Note that the code will currently only work for ATMEL410 / SBRIDGES
179 or ATMEL12350 / EZYNET MIB devices, as MIBs of firmware from
180 other vendors does not seem to support NetworkSettings OID.
181 Exception is ATMEL12350 / NONE (NetGear ME102), whose APCLientInfo
182 OID is capable to give connection status too, but is not currently
183 implemented, since it uses different OID & structure and I do not
184 possess ME102 board to test with (TODO).
186 - hardened input validation for the '-i <ip>' parameter (according to
187 get_ip() in lib/input.c)
188 - added AP MIB type autodetection => utility will now also work
189 for devices with ATMEL12350 MIB. Devices with NWN MIB are yet
190 to be supported (TODO).
191 - assigned credits to Teemu
193 - added definitions for several 'should be defined by default' color
194 pairs, that are actually used in bargraph code of aplink.c .
195 Previous pairs 1,2,3,4 were redefined to 11,12,13,14 to avoid
196 clash with 'standard' color pairs above. This change has been
197 propagated to all files dealing with color pairs.
199 - the same level of changes as in src/ap-auth.c. As side result,
200 it is no longer needed to specify AP MIB type (it will be
202 - bugfix: take into account different length of wirelessStatistics
203 structure in ATMEL12350 MIB & EZYNET extensions => '-t w'
204 will now also work for devices with this MIB & extensions.
205 - bugfix: restrict the '-t l' to ATMEL410 MIB devices in APClient
206 mode (ATMEL12350 MIB devices usually do not return any LinkQuality
207 indicators in wirelessKnownAPs structure).
209 - introduced tftp client for upgrading ATMEL-based AP firmware.
210 Should work with boards utilising either 1.4x.y firmware (generally
211 AT76C510+INTERSIL boards, such as D-Link 1150, W-Link WEN-2021,
212 SmartBridges APPO, etc.), and boards utilising 0.x.y.z firmware
213 (generally AT76C510+RFMD boards, such as Tellus A14, Sparklan
214 WX-1590L, NetGear ME-102, OSBRiDGE p2410/m2410, etc.).
215 Use with care and NEVER EVER try to use this utility to upload
216 firmware that is from different vendor than your AP, unless you
217 perfectly know what you are doing, of course - otherwise,
218 you may irreversibly turn your AP into paperweight quite easily.
219 ATMEL APs are well known for their general firmware upload
220 design flaw (no authorization necessary for firmware upgrade),
221 that has caused many destroyed APs by joe-blow users uploading
222 incorrect firmware, and even APs destroyed by malicious users
223 that have intentionally uploaded incorrect firmware. See manpage
225 You have been warned.
227 - recognise ATMEL12350 enterprise ID => will now react to traps
228 sent by devices with ATMEL 12350 enterprise MIB
229 - will now also print Trap number along with its string
231 - bugfix: fixed problem with printing trap strings from
232 non-SmartBridges traplist when '-s' given, and vice versa
234 - introduced as replacement for old 'auth_mac.c'. Simple 'auth'
235 name reflects its purpose better - it now contains not just
236 MAC-based "auth.", but also other auth. types (Radius, 802.1x)
237 based on the available MIB vendor "extensions".
238 - now properly distinguishes between authorization error and
239 invalid data error for SET snmp() operation. Particularly imporant
240 when user tries to enter Config/MAC Auth menu with user community
241 (which only permits reading, but not writing, and since writing
242 is basically required even for pure showing of authorized MAC
243 addresses, we need to distinguish these errors).
244 If the AP is accessed with 'user' community and it has record(s)
245 in MAC auth. list, it will print '(insufficient community used)'
246 in the first row of the MAC auth. list field.
248 - bugfix: it is now possible to delete last MAC entry too
249 - bugfix: when no MAC address left on the list, disallow 'Delete'
251 - should now be ready for move to lib/. (and purging in src/)
252 - it is now possible to 'escape' from prompt that appears after
253 pressing 'd' (delete MAC), upon entering '0'
254 - by default, if number of defined MACs is greater than the
255 visible scrolling area, the list tail will be shown
256 - if adding new MAC addresses, the list will advance to the last
257 (currently added) MAC entry to show its position in the MAC table
258 - added functionality for HOME, END, PGUP and PGDN keys
259 - added functionality for extra Auth. enhancements present in
260 ATMEL410 MIB with SBRIDGES extensions (Radius auth.), and
261 in ATMEL12350 MIBs with EZYNET extensions (802.1X auth.)
262 - now properly distinguishes MIBs with 2-mode AuthorizationMacEnable
263 OID, and those with 3-mode AuthorizationMacEnable OID
264 - added check against entering duplicated MAC to the MAC table
266 - bugfixes: since SBRIDGES and GEMTEK represent same lvalue, each
267 occurence of ap_vendorext comparison with value SBRIDGES or GEMTEK
268 must be and-ed with result of comparison against ap_type value
269 or all sorts of weirdness may occur (such as non-working options
270 for specific vendor extensions, although they normally should)
271 - bugfixes: revised presence of all OIDs in all actually supported
272 vendor-extended MIBs. Result: all available OIDs relevant to
273 this menu should now also be correctly supported on devices
274 with SmartBridges APPO firmware and NetGear ME102 device firmware.
275 - Label 'Wireless' for config-enabled port mode changed to
276 'Wireless (can be risky)'. I've finally made a resolution
277 to step forward in this - setting config-enabled port to
278 wireless-only can even be deadly for non-USB equipped devices,
279 if configured improperly, if no second ATMEL-based device
280 is handy for fixing conf. on the peer via its wireless port,
281 for outdoor installations, and in couple of other scenarios.
282 REALLY THINK MANY TIMES PRIOR SETTING THIS TO wireless-only !!!
283 * configure.in, src/Makefile.am:
284 - avoid needless linking with curses library for several utilities
285 (ap-auth, ap-mrtg, ap-tftp, ap-trapd).
286 * Sysinfo menu will now also show current 'Operational mode'
287 * bugfix: all conditions that check return value of to snmp(,i,GET)
288 with i > 1, changed from '<= 0' condition to '< i' condition.
289 This is very important in cases when the device does not return _all_
290 the requested varbinds members filled up, which would usually lead
291 either to memory corruption often followed by ap-config crash
292 with 'segmentation fault' reason. If there's unreliable media
293 between the managed device and ap-config, this could previously
294 happen - typically, devices managed via their wireless port
295 or incorrectly configured devices (bad Frag. threshold and/or
296 RTS threshold) may respond with incomplete replies.
297 * naming convention of many variables, structures and OID names changed
298 to respect this scheme (cosmetics, intended coding standard):
299 - names of several #defines changed to be descriptive as
301 - OID names, unless absolutely necessary, should be always named
302 EXACTLY after the corresponding OID name in MIBs for easier
304 - names of structures named after OID, should end with '_s' or
305 '_' followed by something reasonable
306 - variable names should reflect their whole purpose
308 2004-12-09 Roman Festchook
309 * lib/common.c: fixed getting additional character into AP label during autodetection
311 2004-12-09 Michel Robitaille
312 * po/fr.po: updated translation
314 2004-11-28 Roman Festchook
315 * Documentation/ap-gl.8, Documentation/README.ap-gl: info from
316 Documentation/README.ap-gl moved to ap-gl man page, removed
317 Documentation/README.ap-gl
318 * Documentation/README.ap-auth:
319 removed because all info now in ap-auth man page
321 2004-11-28 Roman Festchook
322 * lib/common.c: added checking then function called from ap-gl utility
323 in connect_options() automatic detecting MIB, extention. Now community
324 must be entered manually
325 * lib/ap_search.c: reverted back to scan oid Wireless info string (that find APs even
326 with wrong community) raser than APName oid; info string now truncated only if it
327 cant be displayed at current screen width (now it screen width independed)
328 * Makefile.am: into dist-hook added command to remove po/*.gmo files from
329 final distribution package to decrease size
330 * ap-gl/ap-gl.c: in ap-gl utility reverted back to ATMEL_PRISM rather than ATMEL410 naming
331 * Documentation/ap-config.8: fixed minor bug in example key for 64-bit WEP encryption
332 (http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=243208)
333 * Documentation/ap-gl.8, Documentation/Makefile.am: added man page for ap-gl utility
334 * Documentation/ap-auth.8, Documentation/Makefile.am: added man page for ap-auth utility
335 * po/fr.po: fixed coredump in Config menu with French locale (now just removed long
336 translated string from po file)
337 (http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=259645)
338 * po/uk.po: updated translation
339 * ap-gl/stations.c: fixed RSSI dBm representation
340 * configure.in: version 1.5pre1_FreedomOfUkraine
344 - made WARNING2 more accurate; added WARNING3
346 - added set_oeminfo.c to the list of source modules
348 - QHELP and SELECT #defines moved here from lib/stat.c, as we now
349 reuse them. QHELP renamed to QTHELP (+ toggling mode).
350 - added #defines for NONE, SBRIDGES, TELLUS and VERNET constants
351 with numbering according to new ap_vendorexts[][]. Actual values
352 of these are hold within newly introduced ap_vendorext global
353 (similar to meaning of ap_type global).
354 - new data type 'rdprops', used to describe regulatory domain
355 properties (code, description, first channel, last channel)
356 - formatting fixes (cosmetic)
357 - now #includes lib/ap-curses.h
359 - output formatting changes (unification)
360 - in case the length of AP NAME being displayed for actually
361 scanned AP exceeds 27 characters, truncate the display
362 to first 27 characters (80x25 screen limit) and append
363 '>' character to indicate that not full AP NAME has been
365 - user is now prompted for a community, that will be used
366 to detect APs, prior scanning
368 - introduced new char *ap_vendorexts[][]; moved char *ap_type[]
369 here from src/ap-config.c and ap-gl/ap-gl.c
370 - in favour of proper naming, renamed all *APNAME #defines
371 to *APLABEL (same for texts, with a help message that clearly
372 states that AP LABEL is _independent_ of AP NAME (AP NAME = name
373 stored inside the AP), to prevent eventual user confusion.
374 - all references to 'name' changed to 'label' in order to respect
375 that AP label != AP name (see above). permitted length of label
376 is now max. of 16 characters.
377 - implemented ability to manually select MIB vendor extension
378 along with MIB type (previously just 'AP type:'). This was
379 really necessary as we couldn't rely on get_mib_details()
380 probing especially when the target AP was not available.
381 - if AP MIB type & vendor extension has been _autodetected_, or if
382 there's a good belief that the to-be-connected AP (via
383 connect_options()) is really alive (when we enter connect_options()
384 from ap_search()), then offer possibility to use AP NAME
385 as AP LABEL. However, as AP NAME may have max. length of 31
386 characters, it will be always truncated to first 16 chars
387 (max. length of AP LABEL), and user will be warned if this happens.
388 - introduced new 'rdprops regdom_types[]' field to unify reg. domain
389 description. Along with newly introduced regdom_types[]
390 and regdom_idx(), it enables us to get reg. domain properties
391 related to specific reg. domain code at any time, anywhere.
392 Merged reg. domain codes & properties of MKK1 & ISRAEL freq.
393 domains. Change: MKK domain defines only channel 14.
394 - squashed ch_list() in favour of regdom_types[] => killed malloc()s
395 in wlan.c & test.c. char *channels[] now keeps statically what
396 ch_list() was used to generate on demand before
397 - avoid asking for community upon entering connect_options()
398 called from ap_search(), as we already know the community
399 - thrown myself into about()
401 - all references to 'name' changed to 'label' in order to respect
402 that AP LABEL != necessarilly AP NAME (see above)
403 - implemented storing of MIB vendor extension into ~/.ap-config
404 - changed name of stored file with MAC authorised addresses
405 in the AP from '~/ap-MIBTYPE.stations' to
406 'ap-IP-MIBTYPE-MIBEXT.stations'
407 - output formatting changes (in AP list code):
408 - 'NAME' -> 'LABEL', 'TYPE' -> 'MIB TYPE', newly introduced:
409 'MIB EXT'; accomodate to new layout
410 - in parse_db_str(), truncate displayed length of AP NAME to 16
411 characters (80x25 screen limit), upon length of label being read
412 > 16 characters (80x25 screen width limit), and append '>'
413 character to indicate that it has not been displayed
414 in its full length (TODO: remove screen width limits)
415 - fixed numerous memleaks caused by missing free()ing of
416 ip, passwd and label parts of APList structure in get_opts()
417 - option writing ~/.ap-config is now verbose. Required moving
418 main print_help() to the while(1) cycle body.
419 - save_Stations() is now verbose at minimum level
421 - patched get_value() so that zero-length ANY_STRING type input
422 can be optionally allowed. Selected string input fields now accept
423 empty value. minv & maxv arguments switched from int to unsigned
424 int so that we may cover full uint32 range - also involved
425 switching from atoi() to strtoul(), as we need to check a condition
426 when errno == ERANGE (given value bigger than 0xFFFFFFFF).
427 - implemented wait_key() as unified means to wait for user input
428 selection different ways. The actual input mode with respect
429 to waiting is being held in wait_mode global, that can
430 be toggled using 't/T' keys in statistic views where appropriate
431 (SysInfo, Ethernet statistics, Wireless statistics).
432 - added help_ysn() as preferred & unified way to wait for user Y/N
433 choice. Prints Y/ safe N help message; clear settings subwin
434 & returns 0 upon pressing y/Y or 1 upon n/N. All Y/N code
435 everywhere has been replaced with single call to help_syn().
437 - added hidden call to atmel_set_oeminfo (secret 'OEM info settings'
438 menu), based on set_oeminfo_allowed global from set_oeminfo.c
440 - print_bottom() now also prints MIB vendor extension info
441 in form of 'Ext: <TAG>'
442 - introduced print_bold() to decrease high amount of low-level
443 attribute-setting stuff everywhere (involved conversion
444 to print_bold() wherever possible)
445 - removed print_viewtype() and all references to this replaced
448 - newly introduced. Actually only functional for ATMEL CPU-based
449 APs. ALLOWS TO CHANGE OEM INFORMATIONS STORED WITHIN THE AP,
450 AFTER PRESSING 'S' KEY WHILE IN 'Config' MENU. Note that this
451 is a HIDDEN function, since it is really only suitable for large
452 WISPs & repair shops. Compatibility level that has been achieved
453 with original windows utility is around 96%. Use with care.
455 - added (currently commented out) new function ber_decode_uint().
456 It may come in handy elsewhere in the future.
458 - atmel_sysinfo() now uses select() to wait for user keyboard input.
459 'q' or 'Q' key quits, others force update without clearing screen.
460 - (hopefully) fixed conversion of raw input buffer value to int
461 for uptime-displaying code
462 * lib/sysinfo.c, lib/sysinfo_set.c, lib/wlan.c, lib/ap-utils.h:
464 - added #include <time.h>, missing on some platforms
465 - renamed ptr410 and ptr12350 to str410 and str12350
466 - renamed SysDeviceInfo_* to sysDeviceInfo (MIB conformance)
467 - fixed interpretation of (long) INT value returned by the AP
468 in UpTime-displaying code
469 - implemented toggling of polling mode through 'T' [works
470 only with ATMEL12350 VERNET MIB-compatible devices]
471 - uses select() instead of getch() when polling is active
472 - indentation fixes (cosmetic)
474 - changes to use channels[] and regdom_types[] instead of
475 ch_list() and malloc()s
477 - changes to use channels[] and regdom_types[] instead of
478 ch_list() and malloc()s
479 - fix: added missing print_help(WAIT_RET)
481 - few indentation fixes (cosmetic)
482 - changes to keep sync with new lib functionality (MIB vendor
484 * ap-gl/stations.c, src/stations.c:
485 - print_help() is now called from within while(1) cycle, in order
486 to be compatible with updated save_Stations()
488 - fix: added missing print_help(WAIT_RET)
489 * 'RegulationDomain' renamed to 'RegulatoryDomain' for MIB conformance
490 * further optimisations everywhere for reusing print_bold()
491 * load of small bugfixes
492 * print_title() replaced with new print_top() that will also
493 handle displaying "view" type (on LHS) along with menu title
494 (on RHS) using single pass. This was really in need of unification.
495 Side effect: no need to redraw title strip on each screen update
496 anymore (no two separate ways to write to same location).
497 * some spelling, indentation & accuracy fixes here and there
501 - removed reference to HARDWARE-NOTES, that didnt made it into
502 previous ap-utils versions by accident
503 - added WARNING 1 and WARNING 2 sections (originally intended to be
504 in HARDWARE-NOTES, but the magnitude of their importance deserves
505 to put them straight into README)
508 - added "(valid)" to the ERR_RET message, which more accurately
509 reflects what may actually happen (AP actually _may_ return
510 data, but in an unexpected format)
511 - enhanced WirelessStatistics structure for TransmittedPackets_11Mbps,
512 TransmittedPackets_55Mbps, TransmittedPackets_2Mbps, and
513 TransmittedPackets_1Mbps so that we can support functionally
514 enhanced firmware from VERNET WISP.
516 - in third column, display operAccessPointName OUI using label
517 "Name" instead of Wireless OUI. Makes more sense.
518 - made the number of APs per screen, as well as the offset at which
519 the info about whats actually scanned, is printed, relative
520 to the actual screen height (so to increase maximum hard-coded
521 amount of APs displayed, just switch from 80x25 console font
522 to a bigger one, or use X terminal window)
524 - reverted displaying back to RSSI & LQ both in % in screen 1.
525 This is becouse a) we want to keep as close to the view of the
526 original ATMEL utility as possible here, and b) huge dispersion
527 in dBm versus raw value of RSSI exists among different flavours
528 of APs, and the dBm formula unfortunately often gives results
529 very far from real values. So we want to display something thats
530 less jittering in the scope of inter-AP comparison.
531 - cosmetic fixes (2-line legend instead of 3-line)
532 - rebound the 'refresh' from 's' key to otherwise unused keys,
533 in favour of keyboard interface unification
535 - created get_mib_details() to provide vendor-specific private
537 - fixed a bug introduced by the 'name' patch, resulting in
538 omission to clear screen properly when user has given
539 insufficient credentials (bad password) to detect new AP type
540 - made the 'name'-patch code malloc-free (and memleak #2 free).
541 There's no point to use malloc()d space here since we dont
542 reuse it elsewhere (contrary to char *community).
543 - fixed bad variable boundary-handling introduced by 'name'-patch
544 that might result in crash of utility under circumstance
545 when ~/.ap-config didnt previously exist and user attempted
546 to add new AP with name of length >= 7 characters
547 - added possibility to skip name definition if user wants to
548 (useful for example when the newly added AP's IP will be used
549 solely for testing purposes :)
550 * vendor-specific private ATMEL MIB detection is now referred to
551 get_mib_details() everywhere
553 - a lot of indentation fixes
554 - in get_opts(): fixed couple of bugs:
555 - it was possible to issue 'Connect' command when the AP list
556 was empty (was leading to endless loop)
557 - 'Delete' command failed to remove last remaining AP from the
558 list, ending up in endless loop (as get_value() doesnt do
559 sanity checking on its input paremeters)
560 - fixed a memleak #1 possibly introduced by 'name' patch - we need
561 to free char *name after its use
562 - in _scroll_rows(), fixed the AP MIB TYPE cutoff-by-format-string,
563 introduced by 'name' patch, and enhanced message size to accomodate
564 the true max. row size instead
565 - in get_opts() appended '(in ~/.ap-config)' behind the user-defined
566 APs list banner, to better reflect the real meaning of 'NAME'
567 (and other fields), to prevent someone from f.e. thinking
568 that the NAME here is the name stored in AP's configuration
569 (which it is NOT, of course).
570 * lib/oui.c: added OUIs:
572 - 000D54 (3Com Europe Ltd)
573 - 000D88 (D-Link Corporation)
574 - 000EA6 (ASUSTEK COMPUTER INC.)
576 - fixed non-working radio menu with ATMEL12350 APs by merging the
577 initial TestModeRadioConfiguration and operAntennaSettings OID
578 modifications when ap_type == ATMEL12350
580 - replaced ERR_RET_PRESS with ERR_RET
581 - simplified; no more forking, goto's reduced, no need of
582 pipe(), alarm() or sig*jmp(); use select() for waiting -
583 it is now possible to quit (by pressing 'q' or 'Q') immediately.
584 Also, the counters now get updated immediately after pressing
586 - fixed a bug that, due to previous use of sig*jmp(), resulted
587 in lockup when attempting to quit ap-config after it has received
588 invalid packet, by pressing 'q' key several times
589 - WirelessStat(): implemented support of ATMEL 12350 functionally
590 enhanced MIB by VERNET WISP.
592 - enhanced atmel_sysinfo() for displaying system uptime using
593 UpTime OID from ATMEL12350 VERNET MIB.
595 - fixed showing/setting of BeaconPeriod value for ATMEL12350_TELLUS -
596 acceptable value range is now 0 - 65535 as originally intended
597 - new: implemented showing/setting of 'SIFS time' parameter, specific
598 to APs with ATMEL12350_VERNET firmware/MIB
599 * spelling & indentation fixes
600 * lib/scr.c, src/stations.c:
601 - implemented support for viewing statistics
602 produced by enhanced ATMEL 12350 firmware by VERNET
603 - implemented toggling of RSSI between 'dBm' view, '%' view, and
604 raw view - added new functions print_viewtype_rssi(), conv_rssi().
605 [TODO: update ap-gl/stations.c, too]
606 - pressing other than the selected keys will now result in refresh
609 2004-10-24 Roman Festchook
610 * lib/common.c: fix to clear display before displaying AP type
611 * configure.in: version 1.4.2pre1
613 2004-10-24 Przemyslaw Stanislaw Knycz
614 * po/pl.po: translation updated
616 2004-10-18 Roman Festchook
617 * lib/common.c: fix to use get_value instead of get_pass for input AP name
618 * po/uk.po: translation updated
620 2004-10-18 Teemu Kiviniemi
621 * src/ap-auth.c: command line utility to change the list of authorised MAC addresses added
622 * Documentation/README.ap-auth: some docs for ap-auth utility
624 2004-10-18 Aleksey Korenkov
625 * lib/common.c, lib/file.c, src/ap-config.c: patch that adds name to list of APs
627 2004-08-08 Dan Pelleg
628 * lib/ap_search.c: fix error when build ap-utils on freebsd.
630 2004-06-22 Elif Bilge Maden
631 * po/tr.po: Turkish translation added
633 2004-05-16 Roman Festchook
634 * configure.in: version 1.4.1
635 * NEWS: main changes added
637 2004-05-16 Michel Robitaille
638 * po/fr.po: updated translation
640 2004-05-04 Roman Festchook
641 * lib/ap_search.c: Compiler Error for ap-utils on Darwin 7.3 (Mac OS X 10.3.3) fix
643 2004-04-04 Dieter Fiebelkorn
644 * lib/ap_search.c: Compiler Error for ap-utils on Darwin 7.3 (Mac OS X 10.3.3) fix
646 2004-03-20 Roman Festchook
647 * ap-gl/bridge.c: Isolate wireless clients status displaying fixed
648 * lib/snmp.c: decreased timeout waiting for snmp reply packet to 1 second
649 * src/ap-mrtg.c: to decrease usage of network and AP CPU AP name only requested if -n option specified
651 2004-03-06 Roman Festchook
652 * src/ap-trapd.c: MAc address logging changed to common ap-utils format (without any dividers)
653 * configure.in: version 1.4.1pre3
655 2004-02-27 Roman Festchook
656 * lib/ap-curses.h, configure.in: updates to build with SysV curses lib if ncurses not found
658 2004-02-27 Daniel Eisenbud
659 * lib, src, ap-gl: Solaris and SysV curses build fixes
661 2004-02-26 Roman Festchook
662 * lib/sysinfo.c, lib/wlan.c: fixed Bus error when getting SysInfo structure data from AP on Sun Sparc64 processor
663 * po/uk.po: updated translation
664 * lib, ap-gl, src: removed dublicated includes
665 * lib/ap-utils.h, lib/ap-curses.h, configure.in: updates to build on Solaris with SysV curses lib
668 2004-02-25 Vladimir N.Velychko
669 * Documentation/Ukrainian/*: translation spelling fixes
671 2004-02-25 Roman Festchook
672 * lib, ap-gl, src: removed including config.h from files that include ap-utils.h
673 * lib/ap-utils.h, configure.in: another updates to MacOS X build
675 2004-02-24 Daniel Eisenbud
676 * lib/wlan.c: fix to make ap-config able to set ESSID on powerpc and probably other bigendian machines
678 2004-02-22 Roman Festchook
679 * src/stations.c; ap-gl/stations.c: added check if AP in Client mode with corresponding warning message to user
680 * configure.in: version 1.4.1pre2
682 2004-02-21 Roman Festchook
683 * configure.in: updated to build under MacOS X
685 2004-02-10 Roman Festchook
686 * lib/scr.c: fixed memory leak in scroll_rows function
687 * lib/wlan.c: fixed wrong keys for changing values for NWN APs
689 2004-02-04 Roman Festchook
690 * configure.in: version 1.4
691 * NEWS: main changes added
693 2004-01-30 Roman Festchook
694 * Documentatin/README.ap-gl: added file with notes about ap-gl utility
697 2004-01-29 Roman Festchook
698 * ap-gl: changed ATMEL410 -> ATMEL_PRISM name, for safe use removed Config port blocking, merged wireless client isolation (unicast & broadcast).
700 2003-12-30 Roman Festchook
701 * ap-gl: added new utility for ATMEL410 AP with 1.4k.1 firmware and support for RADIUS auth, wireless clients isolation, Repeater mode, Config port blocking, connected APs extended info (MAC, IP, Parent IP, RSSI, LQ, Status, Port)
702 * lib, src, ap.gl: a lot of internal code moving from program to lib sources
703 * po/uk.po: translation updated
705 * configure.in: version 1.4pre2 "Happy New Year" release
706 * src/bridge.c: renamed options "Send back broadcast/unicast traffic) to Isolate wireless clients
708 2003-12-28 Ashley Gittins
709 * src/ap-mrtg.c: changes to support ATMEL12350/ME-102
711 2003-11-27 Roman Festchook
714 2003-11-27 Jacek Pliszka
715 * ap-utils.spec, Documentation/README.RPM: added spec file for rpm building
717 2003-11-25 Roman Festchook
720 2003-11-23 Roman Festchook
721 * po/uk.po: updated to current sources
722 * src/common.c: changed copyright years to 2001-2003
723 * src/ap-mrtg.c: changed copyright years to 2002-2003
724 * src/aps.c: table header legenda increased to 3 lines
725 * TODO: updated with current goals and removed working now things
726 * configure.in: version 1.3.4pre1
728 2003-11-15 Jacek Pliszka
729 * src/ap-mrtg.c: added -n name option to ap-mrtg that, if used, checks if name of the AP polled is same as one given
731 2003-11-11 Roman Festchook
732 * src/ap-mrtg.c: fixed to return 999999999 for outgoing traffic when error connecting to AP exist
735 * README,THANKS,TODO: modified
736 * HARDWARE-NOTES: added. This should keep important hardware-related
737 informations that the users _must_ read prior using ap-utils.
738 * reverted parameters order for on_off(), menu_choose() so that
739 we always use <row,col> order everywhere
741 - made ap_viewtype global so that the selected view type
742 sustains for whole session
743 - replaced snmp() for SiteSurveyCommand scan with sendto(),
744 as buggy ATMEL12350 firmware does not confirm SiteSurveyCommand
745 reception, but goes straight to internal scanning loop.
746 This allows for attempts to perform SiteSurveyCommand
747 via wireless interface of the AP, which would previously
748 time out due to the reluctance of the firmware to send
749 confirmation, as described above.
750 * src/bridge.c: disallow remote BSSID option key if AP is in
753 - again changed/corrected the order of autodetection.
754 We cannot check against sysDescr OID of ATMEL12350 in first step
755 becouse ATMEL410 devices would pass this check too and would
756 be falsely marked as ATMEL12350.
757 - added back possibility to manually select the AP type.
758 User is given a choice to either autodetect the device
759 (default), or specify type manually. The latter may have
760 advantage if the AP is not actually available via network.
761 - hide cursor again after user turns back from the subshell
762 * src/radio.c: implemented detection & setup functions for APs
763 that give response to operAntennaSettings OID query in 1-byte
764 format. It seems that these devices do not distinguish between
765 receiving and transmitting antennas. This is true even for some
766 APs with single antenna output (Tellus A14 as an example),
767 where this OID gives really no good to the sum of resulting
768 functionality (why would you ever need to set up which antenna
769 is left, right or diversity, if you got just one ? :^)
770 * lib/ap-utils.h, src/common.c, src/input.c:
771 - added new function get_pass(). This code has been taken from
772 common.c, modified and moved to input.c.
773 - AP type is now displayed once it is selected or autodetected
774 - maximum password length is 16 characters, not more (originally
775 it was 32). It is quite possible more than 16 may work
776 with some devices, but I've never seen an AP MIB that would
777 define community length > 16 characters.
778 - made the offsets at which the values are displayed, relative
779 to the length of option name strings, to ease work for
781 - yes_no(): newly introduced
782 - ignore escape key presses in both get_value() and get_pass()
785 - if connect_options() is called for discovered APs, the 'type'
786 argument has to be always > 0, as this is being checked
787 against in connect_options(). We increment it with one all
788 the time and decrement back after the check in connect_options().
789 Now, the user is not prompted for AP type in connect_options()
790 if he should not have to be (originally intended behaviour).
791 - check against duplicated responses from ATMEL410 APs. These
792 are also able to answer queries with 12350 in query OID. This
793 is now being explicitly checked for => no more duplicate
794 ATMEL410 and ATMEL12350 APs with same IPs in the Search menu.
795 - do not attempt to assign const char "public" to 'community'
796 variable, as we attempt to free() it elsewhere. We could use
797 malloc() here, but still, this would have no good reason since
798 user is (and should be) always prompted for a password once
799 he selects desired AP from the 'Search' menu, once it is found =>
800 all password-saving & handling parts have been removed for now.
801 This also fixes a crash that would occur if someone would try
802 to connect to an AP in 'Connect' menu, after unsuccessful
804 - implemented searching per multiple network devices. This involved
805 modifying ap_search() and changing it to scan_local_segment(),
806 as well as making scan_local_segment() self-reentrant, plus
807 adding portable code to scan for available network interfaces
808 for their IP/broadcast(ptp) pairs, that are later used to scan
809 segments via scan_local_segment(). Thanks to Dan J. Bernstein
810 for an effort in writing portable SIOCGIFCONF-related code;
811 the current implementation is based on his ipme.c from Qmail.
812 No more using 255.255.255.255 as broadcast as well as source
813 IP scanning. Results are now accurate even on routers with
814 multiple network interfaces of different types. The current
815 ap_search() has been verified/tested with W-Link WEN2021
816 and Tellus TWL-A14 APs on Linux 2.2/2.4 and FreeBSD 4.9 .
817 - the progress is now verbose:
818 - each AP is shown immediately as soon as it is found
819 - the screen is realtime-updated with information about network
820 interface index, its name and AP type, currently scanned for
821 - it is now possible to quit from scanning process by pressing
822 'q' or 'Q' whenever user wants to
823 - do not attempt to connect to an AP by pressing a key with index
824 of AP that is not present in the 'found' table
825 * src/oui.c: added OUIs:
827 - 000C41 (The Linksys Group, Inc.)
828 * configure.in: added check to determine whether the (struct sockaddr)
829 has 'sa_len' member, and if it has, #define HAVE_SA_LEN in order to
830 properly support network interface detection on 4.4BSD-ish systems.
831 Moved AC_CONFIG_AUX_DIR macro behind AC_INIT, to satisfy
832 newer autoconf. Also, moved template definition from acconfig.h here.
833 * acconfig.h: deleted (deprecated for newer autoconfs)
834 * src/menu.c: added hooks for keys, 'q' / 'Q', Home (PageUp), and
836 * src/set_community.c: use get_pass() for now instead of get_value(),
837 so that the passwords are hidden when someone types them in.
838 We should really use get_value() for this later, and make
839 the password hiding optional.
841 2003-10-21 Roman Festchook
842 * configure.in: version 1.3.3, added "thank you" message
843 * src/common.c: falling back to firstly implemented AP type autodetection order - firstly searching for ATMEL410, by default ATMEL12530
844 * NEWS: main changes added
846 2003-08-14 Roman Festchook
847 * configure.in: version 1.3.3-pre3
850 * README: added several APs to the table of supported hardware
851 * lib/ap-utils.h, src/ap-config.c, src/auth_mac.c: AuthMAC()
852 renamed to atmel_auth_mac()
853 * lib/ap-utils.h, src/input.c, src/test.c, src/set_community.c,
854 src/wep.c, src/wlan.c, src/auth_mac.c, src/bridge.c, src/common.c,
855 src/file.c, src/nwn_advanced.c, src/radio.c:
856 - get_value(): rewritten; now embeds the bounds as well as
857 pressed key checking. The range boundaries, the desired type
858 of input with respect to the acceptable characters, and the
859 pointer to a message to be restored, when a warning about
860 exceeded boundary is printed in the bottom stripe, are accepted
861 as four additional parameters now.
862 - get_ip(), get_mask(): newly introduced
863 - get_ip(), get_mac(): based on get_value(), with additional
864 bounds checking tailored accordingly and moved here from
866 - get_mask(): based on get_ip() with additional mask correctness
867 checking code moved here from src/bridge.c
868 - all the above functions were used to replace the respective
869 original input functions to match the changed prototypes
870 - the generic message 'Invalid value...' has been replaced
871 with 'Value must be in range %i - %i...'. This is printed
872 in bold-white/red in bottom stripe if the user input value
873 exceeds the predefined boundaries.
874 - added inet_aton()-specific includes to lib/ap-utils.h,
875 and removed elsewhere for multiple reasons
876 * src/wlan.c: fixed code displaying the ESSID - upon its change,
877 previously it could happen that if a newly written ESSID
878 would be shorter than the previous one, the loop that has been used
879 to display ESSID would [erroneously] expect the string to be
880 finished with '\0' (which is not required due to operESSIDLength),
881 and would display garbage with content of and length up to an
885 * README: fixed/added some supported AP hardware entries
886 * lib/ap-utils.h, src/ap-config.c, src/bridge.c, src/radio.c,
887 src/set_community.c, src/sysinfo.c, src/test.c, src/wep.c,
888 src/wlan.c: hopefully the last round of changes in naming
890 * src/bridge.c, src/wlan.c:
891 utility now distinguishes some extra MIB subtypes: for 410 enter-
892 prises MIBs: "SmartBridges" form, and for 12350 enterprises MIBs:
893 "Tellus" MIB form "prototype". The MIB form is being distinguished
894 based on the OUI part of MAC address of the device.
895 Other than those MIBs named above are considered "generic"
896 forms, becouse are very ubiquitous.
897 This procedure is necessary, becouse despite the fact that
898 many MIBs keep the same enterprises ID, they differ slightly
899 in OID structures (some OIDs are in one MIB and not in other,
900 and same OIDs even may have significantly different meaning -
901 this is a case of Tellus A14 MIB x NetGear ME102 MIB, f.e.).
902 So, unfortunately, there's no other way, but:
903 - make some MIB "prototypes" (aggregate those that contain
904 exactly the same information, based on the supported
905 AP models across all the device manufacturers)
906 - determine the correct MIB based on the OUI part of MAC
907 address of the device (we assume noone changes OUI part
908 of the MAC of his AP)
909 It is quite possible that this approach will need revision
910 in the future, but since there appears to be no 100% reliable
911 way of how to distinguish different device models of one
912 specific manufacturer, the above is currently the finest,
913 although still coarse enough, method to support most devices.
915 - 'Preferred BSSID' keys rebound from 'm/M' to 'r/R'
916 - 'Forward broadcast traffic' keys rebound from 't/T' to 'r/R'
917 - introduced new setting 'Trap-sending port(s)', and bound to 't/T'
918 key. This setting appears only if ATMEL12350 device with
919 "Tellus Group Co." OUI is detected.
921 - fixed 'Beacon period' input/output data formatting/displaying
922 - display/snag/set 'Beacon period' and 'DTIM sending interval'
923 options/their values only if the device uses "generic"
924 ATMEL12350 MIB prototype (that of NetGear ME102 for example).
925 This should fix crashing becouse of missing MIB OIDs for people
926 that use this kind of devices.
928 2003-08-25 Roman Festchook
929 * lib/ap-utils.h, configure.in: FreeBSD compile time fixes
931 2003-08-19 Roman Festchook
932 * src/ap_search.c: fixed getch delay and restoring current connect options when quiting search screen
935 * README, THANKS: modified
936 * most of string #defines moved from lib/ap-utils.h to the corresponding
937 modules in src - lib/ap-utils.h should keep just those that are
938 common to more than 1 module
940 - fix bound-checking condition. Some APs with older ATMEL firmware
941 actually provide less space than 16 APs in its KnownAP reply,
942 and we also need to check for condition when lvalue of next MAC
943 entry in the response table is 0 (means end of statistics)
944 - only rewrite the current bridge_mode to 3 (AP client) if the
945 AP is ATMEL12350 type
946 * src/auth_mac.c, src/bridge.c, src/nwn_latest.c, src/sysinfo.c,
947 src/test.c, src/wep.c, src/wlan.c:
948 - stripped the formatting characters from remaining string #defines
949 - made the displaying value in 'Feature: value' dependant on offset
950 computed through strlen() from #defined string - this way,
951 the internationalisation is eased becouse translators dont need
952 to keep with original english strings size
953 * src/bridge.c: implemented new functionality from ATMEL 12350 MIB for:
954 - Configuration-enabled port(s)
958 * src/input.c: enhanced get_mac() for checking invalid MAC values
959 that user may type in; if he does, print generic error and loop
960 unless user gives syntactically correct value.
961 * src/radio.c: changed the 'Key' to '[key]' in bottom message for
963 * lib/ap-utils.h, src/sysinfo.c, src/wlan.c: renamed CFG_STRUCT_
964 {ATMEL410,ATMEL12350} to SysDeviceInfo_{ATMEL410,ATMEL12350}
965 * src/wlan.c: corrected offset of displayed values for features:
970 2003-08-14 Roman Festchook
971 * src/common.c: changed AP type autodetection order - firstly searching for ATMEL12350, by default ATMEL410
972 * configure.in: version 1.3.3-pre2
973 * src/aps.c: fixed connecting to choosen AP on ATMEL12350 APs in not AP Client mode
975 2003-08-14 Elros Cyriatan
976 * po/nl/po: New Dutch PO file for `ap-utils'
979 * next round of spelling and indentation fixes
981 - made the 'KnownAP' statistics available only if the Access Point
982 is in AP client mode [original behaviour]. Some Access Points
983 may keep the statistics in their RAM, but no update is performed.
984 Even, sometimes, their RAM may contain garbage after reset,
985 which would cause parsing problems.
986 * lib/ap-utils.h, lib/reset.c, src/ap-config.c, src/ap-mrtg.c,
987 src/ap_search.c, src/aps.c, src/auth_mac.c, src/bridge.c,
988 src/cmd.c, src/common.c, src/radio.c, src/set_community.c,
989 src/stat.c, src/stations.c, src/sysinfo.c, src/test.c,
990 src/wep.c, src/wlan.c:
991 - changed all occurences of 'ATMEL' to 'ATMEL410' and
992 for 'ME102' to 'ATMEL12350'
993 * lib/ap-utils.h, src/ap-config.c, src/sysinfo.c:
994 - renamed sysinfo() to atmel_sysinfo()
995 * lib/ap-utils.h, src/ap-config.c, src/wlan.c:
996 - renamed wireless() to atmel_wireless()
998 - redefined color pair 2 (black ink, green background), and defined
999 new color pair 3 (black ink, green background), and color
1000 pair 4 (white ink, red background). 2 is used for showing
1001 all string values actually changed by the user; 3 is used
1002 for displaying column-info stripe in aps.c, and 4 is used
1003 to display error-related messages in bottom status stripe.
1005 - get_value() modified
1006 * src/scr.c, lib/ap-utils.h:
1007 - added new function print_menusel().
1008 Prints a message split up to two parts - first part without
1009 colors, second part in bright. Used in conjunction with get_value()
1010 to display parameters that the user modified, in bold.
1011 - added new function print_helperr(). This is basically the same
1012 as print_help(), with the only difference that it prints
1013 the text in white bold on red background. Uses color pair 4
1014 and bold attribute; see above.
1015 * names of all print_help() functions related to printing error
1016 messages have been changed to print_helperr()
1017 * src/auth_mac.c, src/bridge.c, src/radio.c, src/test.c, src/wep.c,
1018 src/wlan.c, lib/ap-utils.h:
1019 - implemented new colorisation scheme using print_menusel()
1020 and get_value(), get_mac() - if user enters a new value,
1021 the maximum space (in character counts) that can be used,
1022 is displayed in inverse color. As soon as user confirms
1023 the new value by pressing enter, the changed value is displayed
1024 in bold (so that he knows what he has actually changed).
1026 - when entering AP's IP, mask and gateway, do not allow
1027 to pass further if the user input is invalid - instead, loop unless
1028 user enters valid information
1029 - hardened bounds checking against correct netmask value;
1030 now, invalid netmasks like 255.255.255.129 elicits error
1031 and forces prompt for new value, too
1032 * lib/ap-utils.h, src/ap-mrtg.c, src/ap_search.c: placed
1033 conditinal GLIBC checks => ap-utils now compile/run even
1034 on non-GLIBC (LIBC5-based and such) systems, hopefully.
1035 Actually it has only been tested with libc5-based Linux
1037 * lib/ap-utils.h, src/ap-mrtg.c, src/ap-trapd.c: placed conditional
1038 HAVE_GETTEXT checks around parts using gettext, to get
1039 ap-utils compile on systems without gettext support
1040 * lib/snmp.c, src/file.c: external declaration of ap_type datatype
1041 unified as 'short' and made global to make some old
1042 GNU C compilers happy
1044 2003-08-07 Roman Festchook
1045 * src/brige.c: fixed bug when saving changed ip, netmask and gw
1047 2003-08-07 Jan Rafaj
1048 * various spelling and indentation fixes here and there
1049 * all the ATMEL 12350-specific stuff below has been modelled
1050 using Tellus A14 AP.
1052 - made it malloc()-free. no more potential leaks.
1053 - 'KnownAP' now works for ATMEL 12350-based APs too
1054 - allow of up to 16 concurrent APs to be displayed
1055 in the 'KnownAP', as the packet itself may carry
1056 up to 16 records (768/48). This is also a fix
1057 becouse up to now, the menu has shown just the first
1059 - The button for 'refresh without reset', originally bound to
1060 'g' and 'G' key, has been rebound to 's' ('S') key,
1061 since the keys a-g (A-G) are now used as keys, corresponding
1062 to numbers 10-16 of the APs displayed, when used in
1063 '# connect to this AP' command.
1064 - enhanced '# connect to this AP' functionality for
1065 also setting the appropriate channel through operChannelID
1067 - disallow connection to Ad-Hoc mode bridges
1068 - fixed bad effect of displaying 'Writing data to AP'
1069 after pressing AP number, even if the number of the
1070 selected AP is not actually present in the table
1071 - changed the color scheme to some more eye-pleasant values
1072 - implemented 4 different "views", that can be toggled
1074 * view 1: - most usual one; with RSSI and LQ in %
1075 [ATMEL utility view]
1076 * view 2: - the same as 1; except that RSSI is displayed
1077 in dBm and LQ in raw
1078 * view 3: - ESSID shown expanded to full length,
1079 no NetworkType; RSSI displayed in raw,
1081 * view 4: - shown only BSSID, and its hardware manufacturer
1082 - the 'KnownAP' statistics is available without reset
1083 if the Access Point is either in any of APclient or AP modes,
1084 not just when it is in APclient mode.
1086 - HARD_CONFIGURATION_STRUCT is now replaced with two new
1087 structures: CFG_STRUCT_ATMEL (for ATMEL 410-based devices),
1088 and CFG_STRUCT_ME102 (for ATMEL 12350-based devices).
1090 - sysinfo() made malloc()-free, and made both ATMEL 410-
1091 and ATMEL 12350-aware => SysInfo for APs of both ATMEL types
1092 is now displayed correctly
1094 - added OUI 000CCE (Cisco Systems)
1095 * lib/ap-utils.h, src/wlan.c:
1096 - made it fully ATMEL 410- and ATMEL 12350-aware
1097 (displaying/setting of additional InterRoaming, BeaconPeriod
1098 and DTIM parameters in case of ATMEL12350). Note that
1099 it is possible to regulate BeaconPeriod in range 0-65407
1100 and DTIM in range 0-255, but the boundary limits may vary
1101 with different hardware. I've tried to make as broad
1102 range coverage as possible. Anyway, for example, Tellus A14
1103 resets the BeaconPeriod internally to 100, if you write
1104 it with value out of 1-1000 interval.
1105 - rebound key for ESSID from 'd' ('D') to 'e' ('E')
1107 2003-07-26 Roman Festchook
1108 * src/ap_search.c, src/common.c: changed AP types ATMEL to ATMEL410 and ME102 to ATMEL12350
1109 * src/common.c: added AP type autodetection - by default ATMEL12350
1110 * src/common.c, src/ap_search.c, lib/ap-utils.h: now its possible to choose working AP from AP search result
1111 * po/uk.po: updated translation
1112 * lib/ap-utils.h, src/brige.c: bigendian fixes when setting ip, netmask and gw
1113 * configure.in: version 1.3.3-pre1
1115 2003-06-20 Roman Festchook
1116 * configure.in, acconfig.h, lib/ap-utils.h: small fix to compile under OpenBSD
1117 * po/*.po: fixed some fuzzy translations
1119 2003-06-03 Eugen Hoanca
1120 * po/ro.po, configure.in: added Romanian translation
1122 2003-05-28 Roman Festchook
1123 * configure.in, NEWS: version 1.3.2
1125 2003-05-26 Roman Festchook
1126 * config/config.guess, config/config.sub: updated from latest autoconf
1128 2003-05-21 Roman Festchook
1129 * README: new supported AP added
1130 * configure.in: version 1.3.2-pre4
1132 2003-05-20 Roman Festchook
1133 * src/ap-mrtg.c: fix bug like 2003-05-20 Peter 'p2' De Schrijver patch fixes
1135 2003-05-20 Peter 'p2' De Schrijver
1136 * src/auth_mac.c, src/stat.c, src/sysinfo.c, lib/ap-utils.h: patch to fix ap-config for 64bit archs such as the alpha. It also fixes a minor bug on big endian machines. Patch tested on alpha, ia32, parisc and powerpc.
1138 2003-04-29 Michel Robitaille
1139 * po/fr.po: updated translation
1141 2003-04-28 Roman Festchook
1142 * README: new supported APs added
1143 * src/auth_mac.c: small compile error with old gcc fixed
1145 2003-04-26 Roman Festchook
1146 * README: new supported APs added
1148 2003-04-15 Roman Festchook
1149 * po/pl.po: updated translation
1150 * lib/Makefile.am: not used code exluded for faster compilation
1151 * lib/ap-utils.h: code rearangement
1152 * src/scr.c: some updates for more faster screen handling
1153 * configure.in: version 1.3.2-pre3
1155 2003-04-15 Przemyslaw Stanislaw Knycz
1156 * po/pl.po: fix to correct displaying polish chars
1158 2003-03-13 Roman Festchook
1159 * README: new supported AP from SVEC
1161 2003-02-27 Roman Festchook
1164 2003-02-26 Roman Festchook
1165 * lib/*, src/*, README: added support fpr new Netgear ME102 enterprase in old Atmel mib (ME102 type)
1166 * configure.in: version 1.3.2-pre2
1168 2003-02-25 Roman Festchook
1169 * README: new supported hardware from DCom removed (it's WLink hardware:)
1171 2003-02-23 Roman Festchook
1172 * README: new supported hardware from DCom
1174 2003-02-23 Roman Festchook
1175 * src/menu.c, src/input.c: added new vi-like keys to menu movement
1176 * Documentation/ap-config.8: added info about vi-like keys to menu movement
1177 * configure.in: version 1.3.2-pre1
1179 2003-02-14 Roman Festchook
1180 * TODO: support for ME102 new mib
1181 * configure.in, NEWS: version 1.3.1
1183 2003-02-11 Roman Festchook
1184 * src/wep.c, src/wlan.c: fixed for warnins when compiling by egcs-2.91
1186 2003-02-08 Roman Festchook
1187 * src/common.c: removed unnecessary debug message
1189 2003-02-06 Roman Festchook
1190 * src/input.c, src/mac_auth.c, src/bridge.c. src/nwn_latest.c, src/sysinfo.c, lib/ap-utils.h: mac adresseses now dysplayed and entered like XXXXXXXXXXXX
1191 * Documentation/FAQ: added info about new ME102 AP
1192 * src/ap-search.c: fixed bug with closing sock descriptor after making search - what make impossible working with current AP without reconnect
1194 2003-02-04 Roman Festchook
1195 * src/file.c: fixed updating options file bug
1197 2003-02-03 Roman Festchook
1198 * src/wep.c, Documentation/ap-config.8: added info about WEP key values
1200 2003-01-10 Roman Festchook
1201 * src/common.c: fixed options file name mismatch
1203 2002-12-22 Roman Festchook
1204 * src/file.c: added keys for fast selecting one from first 9 APs, fixed coredump when parsing file in wrong format
1205 * po/uk.po: updated translation
1207 2002-12-16 Roman Festchook
1208 * src/ap-mrtg.c: command line parameters parsing small fix
1210 2002-12-15 Roman Festchook
1211 * configure.in: build cleanups
1212 * src/file.c, src/common.c: now connect option for many APs can be stored in file and current AP can be choosed from it
1213 * src/*, lib/*: many code cleanups and fixes
1215 2002-12-10 Roman Festchook
1216 * configure.in, src/Makefile.am: fixes to build on OpenBSD
1217 * README: new supported OS OpenBSD
1219 2002-12-05 Roman Festchook
1220 * README: supported hardware table updated
1221 * configure.in, NEWS: version 1.3
1223 2002-12-02 Roman Festchook
1224 * src/ap-mrtg.c: fixed printing warning in non verbose mode when getting Link Quality stats
1225 * src/ap-mrtg.c, man/ap-mrtg.8: Signal Strenght returned in dBm
1227 2002-11-25 Roman Festchook
1228 * man/ap-config.8: removed dead link
1230 2002-11-25 Wolfgang Fuschlberger
1231 * Documentation/Ovislink-HOWTO.html: updated howto
1233 2002-11-20 Roman Festchook
1234 * configure.in: defined LIBS and INSTALL variables to compile under QNX (nto-qnx)
1235 * INSTALL: updated with info about installing on QNX
1236 * README: new supported OS added
1237 * src/Makefile.am, configure.in: removed checking for ncurses libs and LIBS difinition moved to Makefile (I think its wrong but useful:)
1238 * src/aps.c, man/ap-config.8: RSSI now displayed in dBm (thanks to Ivan Korshun)
1239 * po/*.po: translations updates
1241 2002-11-11 Michel Robitaille
1242 * po/fr.po: updated french translation
1244 2002-11-10 Roman Festchook
1245 * man/*.8: removed referrer to ap-atmel and ap-nwn
1247 2002-11-10 Dan Pelleg
1248 * src/wlan.c: patch to build on FreeBSD
1250 2002-11-04 Wolfgang Fuschlberger
1251 * Documentation/Ovislink-HOWTO.html: howto use ap-utils with Ovislink hardware
1252 * README: new supported hardware from Ovislink
1254 2002-11-01 Wojciech Puchar
1255 * po/pl.po: polish localization
1257 2002-11-01 Roman Festchook
1258 * lib/common.c, po/*.po: spelling fixes
1260 2002-10-31 Roman Festchook
1261 * src/aps.c: fixed getting info from APs manufactured by CC&C Technologies
1262 * po/*.po: translations updates
1264 2002-10-30 Roman Festchook
1265 * README: new supported hardware
1266 * src/aps.c: check for right channel added
1269 * lib/ber.c: function to ber encode object identifiers added
1271 2002-10-24 Roman Festchook
1272 * configure.in, NEWS: version 1.2
1274 2002-10-21 Pawel P. Kaszynski
1275 * README: new supported hardware from Intellinet
1277 2002-10-17 Michel Robitaille
1278 * po/fr.po: updated french translation
1280 2002-10-15 Roman Festchook
1281 * configure.in: more fixes to compile under netbsd
1283 2002-10-11 Roman Festchook
1284 * lib/common.c: added option to disable saving connect options to file
1286 2002-10-10 Roman Festchook
1287 * src/wlan.c: fixed fail to set essid because wrong len
1288 * Documentation/mib/atmel: new mib added form airBrige device
1289 * src/ap-trapd.c, man/ap-trapd.8: added support for Smartbridges
1290 airBrige traps, run utility with -s key
1291 * src/brige.c: added support for Smartbridges airBrige speciffic oid
1293 2002-10-09 Roman Festchook
1294 * src/brige.c: added check for getted from AP values
1295 * configure.in: added CC variable to compile under netbsd
1296 * README, INSTALL, mib/ap-config.8: updates about merging utilites to ap-config
1298 2002-10-07 Roman Festchook
1299 * src/ap-config.c, lib/common.c, lib/ap-search.c: connect and
1300 search procedure updates
1302 2002-10-07 Dan Pelleg
1303 * lib/ap-search.c: fix to compile under FreeBSD
1305 2002-10-03 Roman Festchook
1306 * src: ap-nwn and ap-atmel merged to one utility ap-config
1307 * lib/snmp.c: decreased timeout waiting for reply from agent - in general it result more faster read SNMP data
1309 2002-10-02 Roman Festchook
1310 * common/ap-search.c: socklen_t variables redefined to uint32_t for build package under MacOS-X
1311 * common/file.c: char variable j redefined as unsigned to socessful build where char is per default unsigned on arm, powerpc and s390.
1312 * nwn/wlan.c: form handling code cleanups, fixed display refreshing after changing antenna and rate options
1313 * README: new supported hardware
1314 * configure.in, NEWS: version 1.1.1
1316 2002-09-29 Roman Festchook
1317 * nwn/advanced.c, man/ap-nwn.8: added some advanced options to optimize long range links and antenna tuning
1319 2002-09-28 Roman Festchook
1320 * atmel/aps.c: now after setting master AP from displated list also setted mode to AP client and ESSID to master AP ESSID, also now AP resets when getting stat only if brige mode = Access Point
1321 * nwn/reset.c, nwn/ap-nwn.c: added option to reset AP
1322 * atmel/wep.c: WEP encryption after fixes works - tested WEP64 crypted link between CompexWP11 and GL2411AP as client
1323 * atmel/ap-trapd.c, man/ap-trapd.8: updated traps list with new traps from 1.4j.1 firmware
1324 * atmel/brige.c: added Repeater mode to Brige modes
1325 * nwn/nwn.c: now possible to define 4 WEP keys and choose default key
1327 2002-09-26 Roman Festchook
1328 * atmel/ap-mrtg.c: small fixes about link quality displaying
1329 * atmel/ap-trapd.c: small log format changes
1330 * README: new supported hardware Smartbridges airBrige and airPoint
1332 2002-09-20 Roman Festchook
1333 * configure.in, NEWS: version 1.1
1335 2002-09-19 Roman Festchook
1336 * atmel/aps.c: interface updates
1337 * po/uk.po, po/fr.po: small translations update
1339 2002-09-19 Andy Igoshin
1340 * atmel/radio.c: now wors fin on big_andian
1342 2002-09-17 Andy Igoshin
1343 * common/ap-utils.h, atmel/wlan.c: basic rates display fix
1344 * man/*.8: man page formatting updates
1346 2002-09-17 Roman Festchook
1347 * nwn/stations.c: rewrited code that get associated stations info to avoid problems with invisible stations
1348 * nwn/stations.c, atmel/stations.c: fixed display last value problem
1349 * po/uk.po, po/fr.po: small translations update
1351 2002-09-16 Roman Festchook
1352 * nwn/stations.c, atmel/aps.c, man/ap-atmel.8, man/ap-nwn.8: display linkquality and signal strenght without any modification on returned values, documentation updates about it
1353 * po/uk.po: translation update
1354 * atmel/aps.c: added option to connect to one of the displayed known APs, also now possible reget and refresh (with reset) stats
1355 * atmel/ap-mrtg.c, man/ap-mrtg.8: aded option to reset AP when getting link quality stats, documentation updates about it, also after reset 10 second timeout set
1357 2002-09-15 Andy Igoshin
1358 * atmel/ap-mrtg.c, atmel/aps.c, atmel/bridge.c, atmel/cmd.c, atmel/stat.c,
1359 atmel/stations.c, atmel/wep.c, atmel/wlan.c, common/ap-utils.h: code cleanups
1360 * nwn/sysinfo.c: code cleanups
1362 2002-09-12 Andy Igoshin
1363 * configure.in: small fix for AIX
1364 * atmel/auth_mac.c, atmel/wep.c: case statement code cleanups
1365 * atmel/auth_mac.c: now works good with big_endian
1366 * common/ap-utils.h: additional macros for data conversion on big_endian
1367 * atmel/brige.c: removed any ip adderess converting on big-endian arch
1368 * atmel/wep.c: now encryption enable and key num works good with big_endian
1370 2002-09-12 Roman Festchook
1371 * nwn/sysinfo.c: removed any ip adderess converting on big-endian arch
1372 * atmel/auth_mac.c: changed type to mib defined
1373 * common/ap-utils.h: swap2 definition to little_endian arch
1374 * atmel/wep.c: some variables declaration moved to up to compile on old gcc compilers
1376 2002-09-11 Roman Festchook
1377 * atmel/wlan.c: fixed unpackeing RegulatoryDomain on big_endian computers
1378 * atmel/bridge.c, nwn/sysinfo.c: fixed ip adderess converting on big-endian arch
1380 2002-09-11 Andy Igoshin
1381 * atmel/sysinfo.c: fixed displaying RegulatoryDomain on big_endian computers
1382 * configure.in: OS definition now standart macro, AIX compilation options
1383 * atmel/auth_mac.c: mac auth foxes for big_endian
1385 2002-09-08 Andy Igoshin
1386 * atmel/Makefile.am, common/Makefile.am, common/ap_search.c,
1387 common/menu.c, common/scr.c, nwn/Makefile.am: patch to compile
1388 by native compiler under AIX 4.3.3
1390 2002-09-08 Roman Festchook
1391 * README: new supported hardware Micronet SP918 and OS AIX 4.3.3 added
1392 * configure.in, common/ap-utils.h, acconfig.h: now big_endian defined
1393 using standart configure macro AC_C_BIGENDIAN (thanks Andy Igoshin
1396 2002-09-06 Roman Festchook
1397 * atmel/bridge.c, nwn/sysinfo.c: fixed ip adderess displaying on big-endian arch
1398 * README: new supported OS MacOS-X
1399 * configure.in: new big_endian arch Power Macintosh
1401 2002-09-04 Roman Festchook
1402 * nwn/wlan.c, atmel/wlan.c: fixed setting channel bug under
1403 Spain and France regulatory domain
1404 * man/nwn.8: additional info about Search AP option
1405 * README: new supported hardware Dlink-1000AP
1406 * nwn/auth_mac.c: displaying mac autorization status fixed
1408 2002-09-02 Roman Festchook
1409 * configure.in, NEWS: version 1.0.5
1410 * po/uk.po: ukrainian translation updates
1412 2002-08-29 Roman Festchook
1413 * atmel/ap-mrtg.c, man/ap-mrtg.8, aclocal.h, configure.in, INSTALL: enable report to MRTG when unable to get stats
1414 from AP now sturtup option, also command line arguments now parse using getopt() in ap-mrtg
1415 * atmel/ap-trapd.c, man/ap-trapd.8, aclocal.h, configure.in, INSTALL: option to change defaul unprivileged user
1416 now sturtup option, also command line arguments now parse using getopt() in ap-trapd
1417 * atmel/brige.c: entering AP mac address in Client mode fix
1418 * common.c, configure.in: macro for check big-endian arch (sparc and mips) now set variable AP_BIG_ENDIAN
1420 2002-08-28 Roman Festchook
1421 * atmel/*.c, nwn/*.c, common/*.c: getting pressed key fixes to avoid reactions to neutral keys pressed by user
1423 2002-08-28 Michel Robitaille
1424 * po/fr.po: french localization
1426 2002-08-27 Roman Festchook
1427 * atmel/stat.c, atmel/test.c, atmel/sysinfo.c, nwn/stat.c: applayed macro swap4 from Erik Rossen for display long values
1428 * configure.in: macro for check big-endian arch (sparc and mips) added
1430 2002-08-27 Erik Rossen
1431 * common/ap-utils.h: added swap4 - a quick-and-dirty macro to unconditionally swap bytes in 4-byte integers between big-endian and little-endian ordering
1432 * INSTALL: instruction to compile under Sparc Linux
1434 2002-08-26 Roman Festchook
1435 * README: updates and spelling
1436 * atmel/test.c: user interface in test mode improvements and fallback when error reading test stat from AP now will not quit tests to make possible restoring normal AP functionality, regulation domain restriction removed
1438 2002-08-19 17:42 Dan Pelleg
1439 * nwn/ap-nwn.c: minor change for compile under FreeBSD
1441 2002-08-08 22:56 Roman Festchook
1442 * configure.in, NEWS: version 1.0.4
1444 2002-08-02 20:29 Roman Festchook
1445 * configure.in: moved configuration utilites into config dir
1446 * atmel/*.c: code rewrited to don't use struct to unpack data that
1447 comes from network (as suggect Erik Rossen its may fix problems
1448 running utility on nonintel computer architectures).
1450 2002-07-24 01:06 Roman Festchook
1451 * configure.in, common/common.c, acconfig.h, INSTALL: added compile
1452 time option to disable regulation domain channel restrictions
1454 2002-07-22 00:02 Roman Festchook
1455 * man/ap-atmel.8, man/ap-nwn.8: added manpages for ap-atmel and ap-nwn
1457 2002-07-21 20:02 Roman Festchook
1458 * man/ap-trapd.8, man/ap-mrtg.8: added manpages for ap-trapd and ap-mrtg
1460 2002-07-21 15:06 Roman Festchook
1461 * nwn/stations.c, atmel/auth_mac.c: getting data from AP algorithms
1464 2002-07-21 01:24 Roman Festchook
1465 * common/oui.c: added displaying AP manufacturer using OUI value
1466 * README: spelling fixes
1468 2002-07-18 14:53 Roman Festchook
1469 * nwn/stations.c: added info about waiting for data when getting
1472 2002-07-16 01:04 Roman Festchook
1473 * configure.in: version 1.0.3
1474 * common/ap_search.c, common/set_community.c: code of search and auth
1475 functions moved into common for both utilites functions
1476 * Makefile.am: now packages will be compressed by bzip2 (to save
1479 2002-07-15 19:31 Roman Festchook
1480 * common/scr.c, common/common.c, common/ap-utils.h: added info about
1481 current AP at right bottom of the screen
1483 2002-07-14 00:20 Roman Festchook
1484 * po, intl, m4: integration with GNU gettext for simlying localization
1486 * src: a lot of internal code optimization and spelling
1487 * nwn/search.c: AP search fixes
1488 * po/uk.po: ukrainian localization
1490 2002-07-07 gettextize <bug-gnu-gettext@gnu.org>
1491 * Makefile.am (SUBDIRS): Add intl.
1492 (ACLOCAL_AMFLAGS): New variable.
1493 (EXTRA_DIST): New variable.
1494 * configure.in (AC_OUTPUT): po/Makefile.in, m4/Makefile.
1496 2002-07-07 05:20 Roman Festchook
1497 * ap-trapd: log additiomal info about agent that generate trap
1499 2002-07-05 02:00 Roman Festchook
1500 * common/ap-cnf.h, *.c: common/ap-cnf.h renamed to common/ap-utils.h
1501 * nwn/menu.c, atmel/menu.c, common/menu.c, common/ap-utils.h,
1502 common/Makefile.am: menu handling code rewrited to one universal
1505 2002-07-04 15:44 Roman Festchook
1506 * configure.in: version 1.0.2
1508 2002-06-29 20:15 Roman Festchook
1509 * nwn/search.c: error messages fixes
1510 * configure.in: added test for Linux
1511 * atmel/ap-trapd.c: fixed displaying new IP when SettingPingIPAddress
1512 trap received, also displaying mac address limited to related traps,
1513 bind to device code compiled only at Linux
1514 * Documentation/README.trapd: info about bind to device option code
1516 * Documentation/THANKS: new contributor Dan Pelleg
1517 * common/ap-cnf.h, README: changed project name to Wireless Access
1518 Point Utilites for Unix
1520 2002-06-28 17:14 Roman Festchook
1521 * atmel/Makefile.am, nwn/Makefile.am, common/Makefile.am: added options
1522 to compile on FreeBSD
1524 2002-06-28 16:45 Dan Pelleg
1525 * atmel/ap-atmel.c, atmel/ap-mrtg.c, atmel/ap-trapd.c, atmel/bridge.c,
1526 atmel/radio.c, atmel/search.c, common/common.c, common/file.c,
1527 common/snmp.c, nwn/ap-nwn.c, nwn/search.c, nwn/sysinfo.c, nwn/wlan.c:
1528 patch to compile and run on FreeBSD
1530 2002-06-26 15:53 Roman Festchook
1531 * configure.in: version 1.0.1
1533 2002-06-24 23:40 Roman Festchook
1534 * ap-trapd: by default installed into '/usr/local/sbin'
1535 * src: code cleanups and compiler warnings fixes
1537 2002-06-21 16:34 Roman Festchook
1538 * */Makefile.am: added target style
1539 * atmel/ap-mrtg: code rearangement
1541 2002-06-17 09:24 Roman Festchook
1542 * README: ap-amtel does work with an D-Link DWL 900AP wich is
1543 (according to some google research it's an Linksys WAP11). Reported
1544 by Jens Link <jenslink at quux dot de>.
1546 2002-06-16 18:48 Roman Festchook
1547 * ap-trapd: added compile time option to set nonprivileged account
1550 2002-06-16 03:12 Roman Festchook
1551 * Makefile: now Makefiles generated by GNU autoconf and automake
1552 * INSTALL: updated with info about new instalation procedures
1553 * ap-mrtg: added compile time option to disable warnings when unable
1555 * atmel/aps.c: removed unnecessary code that read/set remote brige
1557 * atmel/search.c, atmel/wlan.c, nwn/search.c, nwn/wlan.c: compile
1560 2002-06-15 02:10 Roman Festchook
1561 * ap-atmel: added try to restore settings when fail to get KnownAPs
1564 2002-06-09 23:33 Roman Festchook
1566 * ap-mrtg: removed email from usage message
1567 * ap-mrtg and ap-trapd code: placed into atmel directory
1568 * Makefile: some optimization at subdirs and at top level
1569 * Documentation: mibs now back to package
1570 * NEWS, AUTHORS: added
1572 2002-06-08 01:03 Roman Festchook
1573 * ap-trapd: fixed getting data from old trap body when processing
1576 2002-06-06 14:29 Roman Festchook
1577 * ap-trapd: rewriten to log shorter messages without informative
1579 * Documentations: some updates for preparing to version 1.0
1581 2002-06-05 00:01 Roman Festchook
1582 * ap-atmel: added warnings in potentially dangerous options:
1583 KnownAPs, Reset, Upload, Defaults, Restore
1585 2002-06-01 00:20 Roman Festchook
1587 * ap-mrtg: added selecting AP to which get
1588 Link Quality/Signal Strenght statistics, also updated documentation
1590 2002-05-31 00:50 Scott L. Thomas, Roman Festchook
1591 * ap-mrtg: option to get Link Quality/Signal Strenght stat from AP in
1593 * Documentation/README.mrtg: description about getting Link
1594 Quality/Signal Strenght stat from AP in client mode added
1595 * Documentation/README.nwn: added info about basic rates setting
1596 * ap-atmel, ap-nwn: added backspace support when entering password
1598 2002-05-30 14:05 Roman Festchook
1599 * ap-trapd: option to bind listening for traps
1600 on a specific interface added
1601 * Documentation/README.trapd: option to bind listening
1602 for traps on a specific interface described
1603 * Documentation/README.nwn: added info about associated stations
1605 2002-05-29 19:30 Roman Festchook
1606 * ap-nwn: fixed basic rates, AP name and ESSID displaying
1607 * ap-atmel, ap-nwn: some optimization for size
1608 * snmp.c: memory leaks fixes when parsing received packets
1609 * ap-nwn: uptime displaying fixed
1611 2002-05-27 00:03 Roman Festchook
1613 * ap-atmel: added Regulation domain restriction to select channel
1615 * ap-atmel, ap-nwn: added floating dropdown menus for choose from
1618 2002-05-26 16:45 Roman Festchook
1619 * ap-nwn: fixed lenght bug in setting AP name
1621 2002-05-25 14:05 Roman Festchook
1622 * Documentation: added banner image:))
1624 2002-05-22 00:19 Roman Festchook
1626 * Documentation: additions and spelling
1627 * src: removed unused code
1629 2002-05-21 20:06 Roman Festchook
1630 * ap-nwn: added option to find connected APs
1632 2002-05-20 01:37 Roman Festchook
1633 * ap-nwn: added basic rates choose options, added WEP key set options,
1634 added setting prefered channel to operational channel value
1635 * Documentation: mibs excluded from program package (they come with
1636 devices), also excluded power hack docs (readme has links to this
1637 pages) - this greatly reduce package size:)
1639 2002-05-18 19:51 Roman Festchook
1640 * ap-atmel: fixed bug with unable to repeat APs search,
1641 other search fixes and improvements
1643 2002-05-17 15:51 Roman Festchook
1645 * ap-atmel: added option to find connected APs
1647 2002-05-16 00:12 Roman Festchook
1648 * atmel/aps.c: removed timeout when getting KnownAPs stat
1649 from AP in client mode
1651 2002-05-15 20:57 Roman Festchook
1652 * ap-mrtg: added option to get associated stations stat
1653 * README.mrtg: info about stations stat
1655 2002-05-11 08:49 Erik Rossen
1656 * src: fixed compile time errors and warnings
1657 * atmel/scr.c, nwn/scr.c: patch to get rid of the annoying flicker
1658 every time one changes a menu
1660 2002-05-06 02:42 Roman Festchook
1661 * common/file.c: now AP ip and community string saved
1662 in config file ~/.<utility_name>, so no need to
1663 input it after each program start
1664 * common/common.c: connection password at input
1666 * wlan.c: added Regulation Domain limit on setting channel
1667 * atmel/aps.c: Now KnownAP stat may be get without AP reset if AP
1669 * atmel/radio.c: Antenna checks on Atmel, so user can't disable both
1670 antenna, if he do this and save conf - AP restores factory
1671 defaults, now it fixed
1673 2002-05-05 22:39 Roman Festchook
1674 * common/file.c: now Associated Stations list
1675 may be saved to file ~/<utility_name>.stations.
1677 2002-05-04 23:26 Roman Festchook
1679 * README.atmel: added description of most configuration options
1680 * Documentation: updated documentations
1681 * source tree: changed structure
1682 * ap-cnf: renamed to ap-atmel
1684 2002-05-04 18:46 Roman Festchook
1685 * ap-nwn: added utility to config Compex WP11
1687 2002-05-02 18:46 Roman Festchook
1688 * ap-atmel/auth.c: fixed mac number error when deleting addresses
1690 * snmp.c: now returned from agent oid accessible in program
1692 2002-05-01 17:43 Roman Festchook
1693 * snmp.c: added support for Compex WP11 SNMP-agent
1695 2002-05-01 13:01 Roman Festchook
1698 2002-04-30 16:40 Roman Festchook
1699 * src/ap-trapd.c: fixed bug with SettingPingIPAddress trap message
1701 2002-04-27 00:17 Roman Festchook
1702 * src/sysinfo.c: added description for Regulation Domain
1704 2002-04-23 21:12 Roman Festchook
1706 * src/test.c: finished test mode
1707 * docs: documentation updates
1709 2002-04-23 19:00 Roman Festchook
1710 * src/radio.c: added option to enable/disable antennas
1711 * src/menu.c: small menu rearangement again:))
1713 2002-04-22 17:08 Roman Festchook
1714 * src/auth.c: fixed mac number error when deleting addresses from list
1715 * src/menu.c: small menu rearangement
1717 2002-04-15 20:20 Kucherak Sergij, Roman Festchook
1719 * INSTALL, README.ap-cnf: added ukrainian docs
1721 2002-04-15 20:01 Roman Festchook
1722 * src/aps.c: added displaying Link Quality and Signal Strenght
1724 2002-04-14 23:18 Roman Festchook
1725 * src/stat.c: fixed bug, that cause unable to exit
1726 problem when can't to get Ethernet or Wireless stat
1727 * src/aps.c: addded showing Preambule and Wep, also fixed
1728 bug with displaying Network Type
1729 * src/test.c: added unknown OID (see doc/todo),
1730 test mode still not work
1731 * src/snmp.c: fixed some warnings from gcc version pre3
1733 2002-04-14 00:12 Roman Festchook
1734 * src/ap-cnf.c: showing cursor when entering
1735 password/community in connect screen
1737 2002-04-12 00:14 Roman Festchook
1738 * src/auth.c: fixed displaying and setting mac authorization status
1740 2002-04-07 22:32 Roman Festchook
1742 * src/menu.c: added printing tips to all menu options
1744 2002-04-07 13:52 Roman Festchook
1745 * src/Makefile: added 'install' option
1747 2002-04-06 23:50 Roman Festchook
1748 * name: changed name to Access Point SNMP Utils for Linux
1749 * src/stat.c: added mac address displaying in SysInfo,
1750 correctly printed sysinfo string
1751 * README: splited docs at top level directory - added
1752 INSTALL and README.util, added additional info
1754 2002-04-04 22:50 Roman Festchook
1755 * src/ap-trapd.c: after opening socket changed UID and GID
1756 to non root user, I think it's more secure; also
1757 added check from what enterprise this trap came
1758 * src/ap-cnf.c: added info about not displayed characters
1759 when entering password/community
1761 2002-04-04 01:12 Roman Festchook
1762 * src: added info about retrieving/setting data on help string
1763 * src/aps.c: more informative help string
1764 * src/menu.c: option APs renamed to KnownAPs
1766 2002-04-02 14:34 Roman Festchook
1768 * src/aps.c: more verbose info when searching for APs
1769 * README: added warnins about using Statistics/APs option
1770 and info about ap-trapd
1771 * src: code cleanups to remove some warning when compiling gcc 2.9x
1773 2002-04-01 21:36 Roman Festchook
1774 * src/wlan.c: fixed bug with AP name lenght when setting AP name,
1775 this may cause ip address change like
1776 192.168.97.32 => 0.192.168.97. So I think it's critical bug.
1778 2002-03-31 22:58 Roman Festchook
1779 * src/wlan.c: fixed bug with ESSID lenght when setting ESSID,
1780 this make impossible to set ESSID in some cases
1781 * src/trapd.c: added SNMP traps processing daemon
1783 2002-03-27 13:58 Roman Festchook
1785 * src/ap-mrtg: error reports fixes
1786 * src/power.c: power level settings changed,
1787 now optimal values may be experimentally choosed
1789 2002-03-21 14:32 Roman Festchook
1790 * src/smnp.c: conection timeout fixes
1792 2002-03-23 23:16 Roman Festchook
1794 * src/auth.c: fixed bug with mac addresses num = 65535, which mean 0,
1795 this may cause problems configuring absolutelly new AP
1796 * src/aps.c: more safe KnownAPs function - now it restores parameters
1797 after requesting known aps info
1798 * src/cmd.c: upload configuration fixes
1800 2002-03-11 02:01 Roman Festchook
1801 * src/snmp.c: SNMP packets assembly rewriten to work correctly
1802 with packets which size more than 128 bytes
1804 2002-03-09 02:15 Roman Festchook
1806 * src: more verbose parameters description, removed unused code
1807 * ap-cnf: added screen "About", just about me and my program:))
1808 * ap-mrtg: errors printed in MRTG parsable format
1811 2002-03-07 11:20 Roman Festchook
1813 * src/snmp.c: fixed bug with alarm handler
1814 * src/stat.c, src/auth.c: removed mac addresses limit, added
1815 option to save Associated Stations mac addresses to file.
1817 2002-03-03 13:22 Roman Festchook
1819 * src: many small bugfixes and code cleanups
1820 * src/stat.c: Ethernet, Wireless and Wireless environment screens
1821 now refreshed every second with updated data
1822 * src/test.c: start working on test mode settings, but it not useful
1824 * README: new homepage url
1826 2002-03-01 23:53 Roman Festchook
1827 * version: 0.7.1-pre
1828 * src/snmp.c: Wireless stat now count all packets not only Unicast
1829 * src/power.c: setting power level changes
1830 * README: changed info about setting power level
1832 2002-02-28 00:52 Roman Festchook
1833 * src/snmp.c, src/ap-cnf.c, src/ap-mrtg.c: connect blocks fixes
1835 2002-02-27 20:15 Roman Festchook
1836 * src/power.c: power level now displayed with some kind of graph
1838 2002-02-26 14:22 Roman Festchook
1840 * src/wep.c: added Privacy settings, please test
1842 2002-02-25 16:44 Roman Festchook
1843 * spelling: spelling heads up:)) (thanks Charles Henderson)
1845 2002-02-25 14:35 Roman Festchook
1847 * src/ap-mrtg.c: added utility to use MRTG for create stats graphics
1848 * README: added info about using MRTG to request AP
1850 2002-02-24 01:10 Roman Festchook
1851 * src/power.c: added Signal Power settings
1852 * README: added info about Signal Power settings
1855 2002-02-23 16:53 Roman Festchook
1856 * src/bridge.c: added SNMP Traps switch option
1857 * src/wireless.c: interface improvement when setting Basic and
1859 * src/auth.c: socket to AP now opened in nonblock mode
1860 * src/snmp.c: disabled program halt when timeout data read from socket
1864 2002-02-21 22:52 Roman Festchook
1865 * src/bridge.c: fixed broken setting RemoteBSSID in no
1866 Access Point operational modes
1868 2002-02-21 14:17 Roman Festchook
1869 * doc/: added some docs about setting signal power
1870 * doc/mib: added mibs from another APs
1871 * TODO: added setting signal power
1872 * README: added additional info
1873 * src/: new features - new code, version 0.5
1875 2002-02-13 23:22 Roman Festchook
1876 * ChangeLog: There was no ChangeLog here, so I added one.